Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of VICTREX® PEEK 450GL30 BLACK - PEEK-GF30 - Victrex plc

Material Data Center offers the following functions for VICTREX® PEEK 450GL30 BLACK:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Victrex PEEK datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Caractéristiques des transformations/physiquesValeurUnitéNorme du test
ISO Data
Retrait au moulage, parallèle 0.3 % ISO 294-4, 2577
Retrait au moulage, perpendiculaire 0.9 % ISO 294-4, 2577
Conductivité thermique du fondu 0.3 W/(m K) -
Propriétés mécaniquesValeurUnitéNorme du test
ISO Data
Module en traction 11500 MPa ISO 527
Contrainte à la rupture 175 MPa ISO 527
Déformation à la rupture 2.4 % ISO 527
Module de flexion, 23°C 11000 MPa ISO 178
Résistance à la flexion 250 MPa ISO 178
Résistance au choc Izod, +23°C 55 kJ/m² ISO 180/1U
Résistance au choc Izod avec entaille, +23°C 10.5 kJ/m² ISO 180/1A
Dureté Shore D 87.5 - ISO 7619-1
Propriétés thermiquesValeurUnitéNorme du test
ISO Data
Température de fusion, 10°C/min 343 °C ISO 11357-1/-3
Température de transition vitreuse, 10°C/min 143 °C ISO 11357-1/-2
Température de fléchissement s/chrg, 1.80 MPa 328 °C ISO 75-1/-2
Coeffic. de dilatation therm. linéique, parallèle 18 E-6/K ISO 11359-1/-2
Glow Wire Flammability Index (GWFI) 960 °C IEC 60695-2-12
GWFI - thickness tested (1) 2 mm -
Propriétés électriquesValeurUnitéNorme du test
ISO Data
Facteur de pertes, 1MHz 50 E-4 IEC 62631-2-1
Résistivité transversale 5E13 Ohm*m IEC 62631-3-1
Rigidité diélectrique 21.5 kV/mm IEC 60243-1
Indice de résistance au cheminement 150 - IEC 60112
Propriétés diversesValeurUnitéNorme du test
Absorption d'eau 0.3 % Sim. to ISO 62
Masse volumique 1510 kg/m³ ISO 1183
Recommandations pour la transformation Moulage par injectionValeurUnitéNorme du test
Pré-séchage - température 120 - 150 °C -
Pré-séchage - temps 3 - 5 h -
L'humidité de traitement ≤0.02 % -
Température du moule 180 - 200 °C -
Température - Zone d'alimentation ≤100 °C -
Zone 1 360 °C -
Zone 2 370 °C -
Zone 3 375 °C -
Zone 4 380 °C -
Température de la buse 385 °C -
Caractéristiques
Transformation
Moulage par injection, Extrusion (autres)
Conditionnement
Granulés, Noir
Propriétés spéciales
Stérilisable
Résistance Chimique
Résistance chimique générale
Certifications
Contact alimentaire, FDA 21 CFR approbation
Applications
Médical
Disponibilité régionale
Amérique du nord, Europe, Asia Pacific, South and Central America, Proche-Orient/Afrique
Conditions générales
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.